Thrust Block Calculator

Compute reaction force. Thrust block sizing. Incompressible fluid flowing through a horizontal pipe bend.

 
 

Register to enable "Calculate" button. Demonstration mode for mercury

Select fluid and units: Fluid density (lb/ft3):
Flowrate, Q (gpm):
Pipe angle, b (degree):
Upstream diameter, D1 (inch):
Downstream diameter, D2 (inch):
Upstream pressure, P1 (psi):
Downstream pressure, P2 (psi):
Force magnitude, F (lb):
Force direction:
  x-component of Force, Fx (lb):
© 2014 LMNO Engineering, y-component of Force, Fy (lb):
Research, and Software, Ltd. Upstream velocity, V1 (ft/s):
http://www.LMNOeng.com Downstream velocity, V2 (ft/s):
   

Thrust block calculator units: cfm=cubic feet per minute, cfs=cubic feet per second, cm=centimeter, g=gram, ft=foot, gal=gallon (US), gpd=gallons (US) per day, gph=gallons (US) per hour, gpm=gallons (US) per minute, Hg=mercury, hr=hour, H2O=water, in=inch, kg=kilogram, lb=pound, m=meter, mbar=millibar, MGD=Million gallons (US)/day, min=minute, mm=millimeter, N=Newton, Pa=Pascal, psi=pound per square inch, s=second.

Pipe Bend

Discussion
In order to properly calculate the size thrust blocks or other devices to hold a pipe in place, the momentum equation is used to compute the necessary resistive force to hold the pipe stationary. This is also called thrust restraint design. Forces in a pipe bend in the horizontal plane are caused by the fluid's momentum and pressure. If the pipe undergoes a bend in the vertical plane, where the entrance to the bend is above the exit (or vice-versa), then the weight of the liquid and pipe material within the bend will contribute to the force. Since computing the volume of fluid and pipe material within a bend requires considerably more input, we kept our calculation relatively simple by keeping it in the horizontal plane. Our calculation is also valid for incompressible gases, but - due to a gas's low density - the force required to hold a gas pipe in place is typically small compared to the force required to hold a liquid pipe in place unless pressures are high. The forces Fx and Fy computed by the calculation are the x and y components of the total force F.

The four diagrams below further explain the bend angle b and the direction of the calculated force for various situations. The pipe bends are in the horizontal plane. Plain arrow (-->) indicates flow direction. Bold arrow (-->) indicates resistive force that must be applied to keep the bend in place.

Explanation of bend angle and resultant force

Equations
The equations used in our thrust block calculator can be found in nearly any college level fluid mechanics textbook (e.g. Munson et al., 1998) or fluid mechanics reference handbook. The force equations are based on linear momentum conservation. P2 is computed using the Bernoulli Equation, which assumes negligible friction loss around the bend.

Subscript 1 is upstream of bend; Subscript 2 is downstream of bend; Subscript x is x-component of force; Subscript y is y-component of force. For a pipe bend in the horizontal plane where friction effects around the bend are negligible:

Fx = -P1A1 - P2A2 cos(b) - d Q [V1 + V2 cos(b)]

Fy = P2 A2 sin(b) + d V2 Q sin(b)     F = (Fx2 + Fy2)1/2

Q=VA       A=π D2 / 4

P2 = P1 + d (V12 - V22) / 2

Variables
To use the equations above, a consistent set of units must be used. The variables below show the SI (System International) units for each variable. Our calculation allows a variety of other units with the conversions made internally within the program.
A=Pipe flow area (m2)
b=Pipe angle shown in the figure above (valid range is 0 to 2π radians or 0 to 360o)
d=Liquid (or gas) mass density (kg/m3)
D=Pipe diameter (m)
F=Resistive (reaction) force (N)
P=Gage pressure (N/m2, relative to atmospheric pressure)
Note: P1 and P2 cannot physically be below 0.0 absolute pressure (-101,325 N/m2 gage). Further, if P1 or P2 approach the liquid's vapor pressure, flashing to vapor may occur and the calculation will not be accurate. Vapor pressure is not checked by the program, but a message will appear if P1 or P2 is less than -101,325 N/m2 gage.
Q=Flowrate (m3/s)
V=Velocity (m/s)
π=Greek letter pi, 3.1415926....

Messages given by calculation
"Need Density>0", "Need Q>0", "Need D1>0", "Need D2>0", "Need pipe angle b>0", "Need P1>0 absolute", "Need 0 < b < 6.28 radian", "Need 0 < b < 360 degrees". These are initial checks of input data.

"Need P2>0 absolute". Message will appear after computing downstream pressure. Physically, pressure cannot be less than 0.0 absolute, which is a complete vacuum. The calculation method does not account for liquid flashing to vapor if the pressure drops below the liquid's vapor pressure.

Reference
Munson, Bruce R., Donald F. Young, and Theodore H. Okiishi. 1998. Fundamentals of Fluid Mechanics. John Wiley and Sons, Inc. 3ed.

© 1999-2024 LMNO Engineering, Research, and Software, Ltd.  All rights reserved.

Please contact us for consulting or questions about hydraulic forces on pipe bends.

LMNO Engineering, Research, and Software, Ltd.
7860 Angel Ridge Rd.   Athens, Ohio 45701  USA   Phone: (740) 707-2614
LMNO@LMNOeng.com    https://www.LMNOeng.com

To: 
LMNO Engineering home page (more calculations)  

Related calculations:

Darcy-Weisbach incompressible flow calculator 

Unit Conversions

Register