LMNO Engineering logo LMNO Engineering, Research, and Software, Ltd.

Partially Full Cylinder, Sphere, and Cone Volume Calculator

Calculations and equations for partially full storage tanks: Partially full cylindrical tank on its side, partially full spherical container, and conical shape

Register to enable "Calculate" button.

Select shape:
www.​LMNOeng.com
Liquid Depth, y: 
Diameter, D: 
Liquid Top Width, T: 
Cylinder Length, L: 
Volume, V: 
© LMNO Engineering, Research, and Software, Ltd.


Units: barrel=42 US gallons, cm=centimeter, ft=feet, gallon=US gallon, km=kilometer, m=meter


Sphere, Cylinder, Cone Diagrams

Equations for Sphere, Cylinder, and Cone Volume (Rade and Westergren, 1990)

Partially full sphere, cylinder, cone equations

Discussion

This web page is designed to compute volumes of storage tanks for engineers and scientists; however, it may be useful to anyone who needs to know the volume of a full or partially full sphere, cylinder, or cone. Technically, our "cone" is not really a cone; it is a "frustum of a right cone" (Rade and Westergren, 1990, p. 73). A cone is a frustum that has a top diameter of 0.0. For the cylinder laying on its side, if you enter liquid top width, diameter, and length, there are two possible solutions for depth and volume; therefore, when using the drop-down menu to select which calculation to perform, you must select whether the cylinder is more or less than half full.


Variables


D = Sphere or cylinder diameter [L].
Dbot = Cone bottom diameter [L].
Dtop = Cone top diameter [L].
h = Cone height [L].
L = Cylinder length [L].
T = Top width of liquid in cylinder [L].
V = Volume of liquid in cylinder, cone, or sphere [L3].
y = Liquid depth in sphere or cylinder [L].
z = Horizontal to vertical side slope of cone.  z<0 if Dtop<Dbot.  z=0 if Dtop=Dbot.  z>0 if Dtop>Dbot.
θ = Angle representing how full the cylinder is [radians or degrees].  An empty cylinder has θ=0o,  a cylinder with θ=180o is half full, and a cylinder with θ=360o is completely full.


Error Messages

"D must be > 0." Cylinder diameter was entered as ≤ 0; it must be positive.
"D's must be ≥ 0." Dtop or Dbot for the cone was entered as negative.
"h must be ≥ 0." Cone height was entered as negative.
"L must be > 0." Cylinder length was entered as ≤ 0.
"T must be ≥ 0." Cylinder top width was entered as negative.
"T must be ≤ D." Cylinder liquid top width cannot be greater than cylinder diameter.
"y must be ≥ 0." Sphere or cylinder liquid depth was entered as negative.
"y must be ≤ D." Sphere or cylinder liquid depth cannot be greater than diameter.
"Infeasible. Dbot will be < 0." The slope that was input for the cone gives a bottom diameter that is negative, which is physically impossible. Most likely the slope was entered with an incorrect sign. Slope is Horizontal/Vertical and is negative for a cone with a smaller top than bottom.
"Infeasible. Dtop will be < 0." Similar to above.


Reference

Rade, Lennart and Westergren, Bertil. 1990. Beta Mathematics Handbook. CRC Press. 2ed.


© 2000-2024 LMNO Engineering, Research, and Software, Ltd.  All rights reserved.

LMNO Engineering, Research, and Software, Ltd.
7860 Angel Ridge Rd.   Athens, Ohio  45701   USA   Phone: (740) 707-2614
LMNO@LMNOeng.com    https://www.LMNOeng.com